Pioneer Car Stereo System CD Receiver User Manual

2.8

Out of 2 Ratings

Owner's of the Pioneer Car Stereo System CD Receiver gave it a score of 2.8 out of 5. Here's how the scores stacked up:

  • Reliability

    3.0 out of 5

  • Durability

    3.5 out of 5

  • Maintenance

    2.0 out of 5

  • Performance

    3.5 out of 5

  • Ease of Use

    2.0 out of 5
of 96
 
Black plate (21,1)
Installation
Important
! Check all connections and systems before
final installation.
! Do not use unauthorized parts as this may
cause malfunctions.
! Consult your dealer if installation requires
drilling of holes or other modifications to the
vehicle.
! Do not install this unit where:
— itmay interfere withoperation of the vehicle.
— itmay cause injury to apassenger as aresult
of asudden stop.
! The semiconductor laser will be damaged if
it overheats. Install this unit away fromhot
places such as near the heater outlet.
! Optimum performance is obtained when the
unit is installed at an angle of lessthan 60°.
60°
! When installing, to ensure proper heat dis-
persal when using this unit, make sure you
leave ample space behind the rear panel and
wrap any loose cables so they are notblock-
ing the vents.
5cmcm
Leave ample
space
5 cm
5 cm
DIN front/rear mount
This unit can be properly installed using either
front-mount or rear-mount installation.
Use commercially available parts when instal-
ling.
DIN Front-mount
1 Insert the mounting sleeve into the dash-
board.
For installation inshallow spaces, use the sup-
plied mounting sleeve. If there is enough space,
use the mounting sleeve that came withthe ve-
hicle.
2 Secure the mounting sleeveby using a
screwdriver to bend the metaltabs (90°) into
place.
1
2
1 Dashboard
2 Mounting sleeve
# Make surethat the unit isinstalled securely in
place. Anunstable installation maycause skipping
or othermalfunctions.
DIN Rear-mount
1 Determine the appropriate position
where the holes on thebracket and the side
of the unit match.
2 Tighten two screws on eachside.
1
2
3
1 Screw
2 Mounting bracket
3 Dashboard or console
! Use eithertruss (5mm × 8mm) or flushsur-
face (5mm ×9mm) screws, dependingon
the bracketscrew holes.
Removing the unit
1 Remove the trim ring.
1 Trimring
2 Notched tab
! Releasing thefront panel allowseasier ac-
cess tothe trim ring.
! When reattachingthe trim ring,point the
side withthe notched tabdown.
2 Insert the supplied extraction keys into
both sides of the unit until theyclick into
place.
3 Pull the unit out of the dashboard.
Removing and re-attaching the
front panel
You can remove the front panel to protect your
unit from theft.
For details,refer to Removing the front panel and
Re-attaching the front panel on page 4.
Securing the front panel
The front panel can be secured withthe sup-
plied screw.
1
1 Screw
Installing the microphone
Only for DEH-X6600BS, DEH-X6600BT, DEH-X66BT
and DEH-X4600BT
CAUTION
It is extremely dangerous to allow the micro-
phone lead to become wound around thesteer-
ing column or shift lever. Besure to install the
unit in such a way that it willnot obstruct driv-
ing.
Notes
! Install the microphone in a position and ori-
entation that will enable it to pick upthe
voice of the person operating the system.
English
Installation
21
Section
Installation
En
04
<QRD3195-A>21

   Find Your Products By Category