Kenwood Car Stereo System Kenwood Car Stereo System User Manual

3.0

Out of 1 Ratings

Owner's of the Kenwood Car Stereo System Kenwood Car Stereo System gave it a score of 3.0 out of 5. Here's how the scores stacked up:

  • Reliability

    3.0 out of 5

  • Durability

    3.0 out of 5

  • Maintenance

    3.0 out of 5

  • Performance

    3.0 out of 5

  • Ease of Use

    3.0 out of 5
of 44
 
6
Item Selectable setting (Preset: *)
PRESET TYPE NORM *: Memorizes one station for each preset button in each band (FM1/ FM2/ FM3/ AM). ;
MIX: Memorizes one station for each preset button regardless of the selected band (FM1/ FM2/ FM3/ AM).
KEY BEEP ON */ OFF: Activates/deactivates the keypress tone.
BUILTIN AUX ON1 *: Outputs sound of the connected external component when “AUX” is selected as the source. ;
ON2: Outputs sound from the connected external component when “AUX” is selected as the source. When you
turn on the power, the sound attenuates (to prevent noise when no external component is connected). Turn the
volume knob clockwise to return to the previous volume level. ; OFF: Disables “AUX” in source selection.
CD READ 1 *: Automatically distinguishes between audio file disc and music CD. ; 2:
Forces to play as a music CD.
SWITCH PRE REAR */ SUB-W: Selects whether rear speakers or a subwoofer are connected to the line out terminals on the
rear of the unit (through an external amplifier).
SP SELECT OFF */ 5/4/ 6 × 9/6/ OEM: Selects the speaker size for optimum performance.
Getting started
Canceling the display
demonstration
The display demonstration is always turned
on unless you cancel it.
When you turn on the power (or after you
reset the unit), the display shows:
[CANCEL
DEMO] \ [PRESS] \
[VOLUME KNOB]
1
Press the volume knob.
[YES] is selected as the initial setup.
2
Press the volume knob again to confirm.
[DEMO
OFF] appears.
If no operation is done for about
15 seconds or if you turn the volume knob
to select [NO] in step
2
, [DEMO
MODE]
appears and the display demonstration
starts.
Setting the demonstration mode
1
Press the volume knob to enter
[FUNCTION].
2
Turn the volume knob to select
[DEMO MODE], then press to enter.
3
Turn the volume knob to select [ON] or
[OFF].
If [ON] is selected, display demonstration
starts if no operation is done for about
20 seconds.
4
Hold to finish the procedure.
Adjusting the clock
1
Press the volume knob to enter
[FUNCTION] mode.
2
Turn the volume knob to select
[SETTINGS], then press to enter.
3
Turn the volume knob to select [CLOCK],
then press to enter.
4
Press the volume knob to select
[CLOCK ADJ], then press to enter.
Clock hour flashes on the display.
5
Turn the volume knob to adjust the
hour, then press to enter minute
adjustment.
Clock minutes flashes on the display.
6
Turn the volume knob to adjust the
minute, then press to confirm.
Press 4
/
¢ to move between the
hour and minute adjustment.
7
Hold to finish the procedure.
Initial settings before operations
1
Press SRC to enter [STANDBY] mode.
2
Press the volume knob to enter
[FUNCTION] mode.
3
Turn the volume knob to select
[INITIAL SET], then press to enter.
4
Turn the volume knob to make a
selection, then press to confirm.
See table below for selection.
5
Hold to finish the procedure.
EN02-15_KDC-152[K]1.indd 6EN02-15_KDC-152[K]1.indd 6 5/6/11 3:01:31 PM5/6/11 3:01:31 PM

   Find Your Products By Category